001008356 001__ 1008356
001008356 005__ 20240708132659.0
001008356 037__ $$aFZJ-2023-02302
001008356 041__ $$aEnglish
001008356 1001_ $$0P:(DE-Juel1)129591$$aBram, Martin$$b0$$eCorresponding author$$ufzj
001008356 1112_ $$aElectric field enhanced processing of advanced materials III: Complexities and opportunities$$cTomar$$d2023-03-19 - 2023-03-24$$gTomar III$$wPortugal
001008356 245__ $$aUltra-fast high temperature sintering (UHS) of strontium titanate
001008356 260__ $$c2023
001008356 3367_ $$033$$2EndNote$$aConference Paper
001008356 3367_ $$2DataCite$$aOther
001008356 3367_ $$2BibTeX$$aINPROCEEDINGS
001008356 3367_ $$2DRIVER$$aconferenceObject
001008356 3367_ $$2ORCID$$aLECTURE_SPEECH
001008356 3367_ $$0PUB:(DE-HGF)6$$2PUB:(DE-HGF)$$aConference Presentation$$bconf$$mconf$$s1688374140_3226$$xOther
001008356 520__ $$aRecently, ultra-fast high-temperature sintering (UHS) has been introduced as novel fast sintering method. UHS enables rapid densification of ceramic materials within seconds [1]. Therefore, green compacts are placed between thin strips of carbon felt, which are then heated by direct current. Joule heating of the stripes enables extremely high heating rates beyond 104 K/min. In the present work, strontium titanate and 2 mol. % iron doped strontium titanate were used as model materials for systematically studying the relationship between UHS parameters and resulting properties [2]. Similar to other fast sintering technologies, exact control and measurement of temperature and the occurrence of larger temperature gradients remain challenging. Therefore, FEM modelling was conducted to estimate the temperature distribution of setup and sample. FEM model was validated by thermocouple, pyrometer and melt phase formation at predicted temperatures. Figure 1 exemplarily shows the temperature distribution of the used setup (carbon stripe 80 x 10 x 4 mm heated by DC current varying between 5 and 24 A). A special focus was to investigate the influence of the applied current on degree of densification and resulting grain size. For both materials, rapid densification of small samples (diameter 8 mm, height 1 mm) within 10 s was demonstrated successfully. In the case of undoped strontium titanate, exaggerated grain growth in combination with the formation of isolated pores was observed. The addition of 2 mol. % iron helped to limit the grain growth and therefore enabled a more uniform densification and grain growth. On the other hand, these samples were more susceptible to cracking, especially at higher currents. Segregation of cations at grain boundaries was analysed by scanning transmission electron microscopy/energy disperse x-ray spectroscopy (STEM/EDS). Electrical performance of both materials was demonstrated by impedance spectroscopy. A comparison of the conductivity of UHS sintered and conventionally sintered samples did not show remarkable differences.
001008356 536__ $$0G:(DE-HGF)POF4-899$$a899 - ohne Topic (POF4-899)$$cPOF4-899$$fPOF IV$$x0
001008356 7001_ $$0P:(DE-Juel1)166597$$aMishra, Tarini Prasad$$b1
001008356 7001_ $$0P:(DE-HGF)0$$aWang, Shufan$$b2
001008356 7001_ $$0P:(DE-Juel1)138081$$aLenser, Christian$$b3$$ufzj
001008356 7001_ $$0P:(DE-Juel1)190607$$aJennings, Dylan$$b4$$ufzj
001008356 7001_ $$0P:(DE-Juel1)174079$$aKindelmann, Moritz$$b5$$ufzj
001008356 7001_ $$0P:(DE-Juel1)185039$$aRheinheimer, Wolfgang$$b6$$ufzj
001008356 7001_ $$0P:(DE-HGF)0$$aBroeckmann, Christoph$$b7
001008356 7001_ $$0P:(DE-Juel1)161591$$aGuillon, Olivier$$b8$$ufzj
001008356 909CO $$ooai:juser.fz-juelich.de:1008356$$pVDB
001008356 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)129591$$aForschungszentrum Jülich$$b0$$kFZJ
001008356 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)138081$$aForschungszentrum Jülich$$b3$$kFZJ
001008356 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)190607$$aForschungszentrum Jülich$$b4$$kFZJ
001008356 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)174079$$aForschungszentrum Jülich$$b5$$kFZJ
001008356 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)185039$$aForschungszentrum Jülich$$b6$$kFZJ
001008356 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)161591$$aForschungszentrum Jülich$$b8$$kFZJ
001008356 9131_ $$0G:(DE-HGF)POF4-899$$1G:(DE-HGF)POF4-890$$2G:(DE-HGF)POF4-800$$3G:(DE-HGF)POF4$$4G:(DE-HGF)POF$$aDE-HGF$$bProgrammungebundene Forschung$$lohne Programm$$vohne Topic$$x0
001008356 9141_ $$y2023
001008356 920__ $$lyes
001008356 9201_ $$0I:(DE-Juel1)IEK-1-20101013$$kIEK-1$$lWerkstoffsynthese und Herstellungsverfahren$$x0
001008356 980__ $$aconf
001008356 980__ $$aVDB
001008356 980__ $$aI:(DE-Juel1)IEK-1-20101013
001008356 980__ $$aUNRESTRICTED
001008356 981__ $$aI:(DE-Juel1)IMD-2-20101013