001047598 001__ 1047598
001047598 005__ 20251104202046.0
001047598 020__ $$a978-3-95806-861-2
001047598 0247_ $$2datacite_doi$$a10.34734/FZJ-2025-04401
001047598 037__ $$aFZJ-2025-04401
001047598 1001_ $$0P:(DE-Juel1)188130$$aSchmitt, Johannes-Christian$$b0$$eCorresponding author$$ufzj
001047598 245__ $$aBewertung lokaler Eigenspannungsverteilungen bei der lokalen Bauteilreparatur durch Kaltgasspritzen$$f - 2025-03-11
001047598 260__ $$aJülich$$bForschungszentrum Jülich GmbH Zentralbibliothek, Verlag$$c2025
001047598 300__ $$a154, xxvii
001047598 3367_ $$2DataCite$$aOutput Types/Dissertation
001047598 3367_ $$0PUB:(DE-HGF)3$$2PUB:(DE-HGF)$$aBook$$mbook
001047598 3367_ $$2ORCID$$aDISSERTATION
001047598 3367_ $$2BibTeX$$aPHDTHESIS
001047598 3367_ $$02$$2EndNote$$aThesis
001047598 3367_ $$0PUB:(DE-HGF)11$$2PUB:(DE-HGF)$$aDissertation / PhD Thesis$$bphd$$mphd$$s1762266685_19382
001047598 3367_ $$2DRIVER$$adoctoralThesis
001047598 4900_ $$aSchriften des Forschungszentrums Jülich Reihe Energie & Umwelt / Energy & Environment$$v680
001047598 502__ $$aDissertation, Bochum, 2025$$bDissertation$$cBochum$$d2025
001047598 520__ $$aIn recent years, there has been a notable increase in interest in cold spraying, largely due to its potential applications in repair and additive manufacturing. Nevertheless, further research is required to gain insight into the residual stress state and mechanical integrity of cold sprayed coatings. This thesis is concerned with the repair of Inconel 718 components. Such components are employed in gas turbines and other applications due to their exemplary material properties. In this context, a cavity was created, based on the typical repair process, with a depth of 4 mm and 60° conical walls, as a result of the milling process, for the purpose of crack removal. The filling of such deep cavities with Inconel 718 results in the formation of a dense coating with good adhesion. A comprehensive residual stress analysis of the entire cavity was conducted using neutron diffraction, with near-surface measurements supplemented by the incremental hole-drilling method. The resulting residual stress state was found to be direction-dependent due to the geometric limitations of the cavity, as expected, but the specific gas conditions showed the anticipated results. Further experiments were conducted to investigate the effects of different robot speeds by in situ curvature measurements using the ICP sensor. Based on the findings, an analytical model was developed to estimate the resulting temperature gradient at the gas spot. These findings are supported by particle diagnostics and data from an implemented, three-dimensional CFD model in ANSYS Fluent. The results were also used to vary the resulting spray spot of different nozzle geometries in the context of additive manufacturing and to discuss the resulting residual stresses in conjunction with the data pertaining to the gas and particles. The results demonstrate that the restoration of Inconel 718 components by means of cold spraying results in the formation of dense repair coatings with good mechanical properties. The residual stress state is anisotropic, depending on the geometric limitations. In general, it is possible to systematically adjust the residual stress state in cold sprayed coatings by modifying the process parameters and the nozzle geometry in order to achieve the desired stress state. The present work was carried out within the framework of the DFG project VA163/11-1.
001047598 536__ $$0G:(DE-HGF)POF4-1241$$a1241 - Gas turbines (POF4-124)$$cPOF4-124$$fPOF IV$$x0
001047598 8564_ $$uhttps://juser.fz-juelich.de/record/1047598/files/Energie_Umwelt_680.pdf$$yOpenAccess
001047598 909CO $$ooai:juser.fz-juelich.de:1047598$$popenaire$$popen_access$$pVDB$$pdriver$$pdnbdelivery
001047598 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)188130$$aForschungszentrum Jülich$$b0$$kFZJ
001047598 9131_ $$0G:(DE-HGF)POF4-124$$1G:(DE-HGF)POF4-120$$2G:(DE-HGF)POF4-100$$3G:(DE-HGF)POF4$$4G:(DE-HGF)POF$$9G:(DE-HGF)POF4-1241$$aDE-HGF$$bForschungsbereich Energie$$lMaterialien und Technologien für die Energiewende (MTET)$$vHochtemperaturtechnologien$$x0
001047598 9141_ $$y2025
001047598 915__ $$0StatID:(DE-HGF)0510$$2StatID$$aOpenAccess
001047598 915__ $$0LIC:(DE-HGF)CCBY4$$2HGFVOC$$aCreative Commons Attribution CC BY 4.0
001047598 920__ $$lyes
001047598 9201_ $$0I:(DE-Juel1)IMD-2-20101013$$kIMD-2$$lWerkstoffsynthese und Herstellungsverfahren$$x0
001047598 980__ $$aphd
001047598 980__ $$aVDB
001047598 980__ $$aUNRESTRICTED
001047598 980__ $$abook
001047598 980__ $$aI:(DE-Juel1)IMD-2-20101013
001047598 9801_ $$aFullTexts