001053957 001__ 1053957
001053957 005__ 20260227202312.0
001053957 020__ $$a978-3-95806-877-3
001053957 0247_ $$2datacite_doi$$a10.34734/FZJ-2026-01634
001053957 037__ $$aFZJ-2026-01634
001053957 1001_ $$0P:(DE-Juel1)188375$$aRüßmann, Martin$$b0$$eCorresponding author
001053957 245__ $$aEntwicklung von Beschichtungsverfahren für die Herstellung von Wärmedämmschichten auf additiv gefertigten Komponenten$$f - 2025-05-15
001053957 260__ $$aJülich$$bForschungszentrum Jülich GmbH Zentralbibliothek, Verlag$$c2026
001053957 300__ $$aix, 188
001053957 3367_ $$2DataCite$$aOutput Types/Dissertation
001053957 3367_ $$0PUB:(DE-HGF)3$$2PUB:(DE-HGF)$$aBook$$mbook
001053957 3367_ $$2ORCID$$aDISSERTATION
001053957 3367_ $$2BibTeX$$aPHDTHESIS
001053957 3367_ $$02$$2EndNote$$aThesis
001053957 3367_ $$0PUB:(DE-HGF)11$$2PUB:(DE-HGF)$$aDissertation / PhD Thesis$$bphd$$mphd$$s1772191377_12913
001053957 3367_ $$2DRIVER$$adoctoralThesis
001053957 4900_ $$aSchriften des Forschungszentrums Jülich Reihe Energie & Umwelt / Energy & Environment$$v687
001053957 502__ $$aDissertation, Bochum, 2025$$bDissertation$$cBochum$$d2025
001053957 520__ $$aThe protection of metallic combustion chamber walls and high-temperature blades in aircraft turbines by ceramic thermal barrier coatings (TBC) and air film cooling is crucial for increasing the efficiency and service life of the turbine. A further improvement in efficiency requires an increase in the gas inlet temperature, which necessitates the development of optimized WDS systems and cooling concepts. Additive manufacturing technologies facilitate the production of flow-optimized cooling holes, which form an insulating layer of air on the hot WDS surface using compressor air during turbine operation, thus protecting it from the hot combustion gases. However, to ensure a continuous air film, the cooling holes must not be blocked by the bonding agent layer (bond coat) or the top coat. The subsequent opening of complex geometries using mechanical processes or laser technology is time-consuming and cost-intensive, necessitating the development of suitable coating processes that avoid blocking the cooling holes. As part of this study, the propensity for blockage of several bond coat production techniques was assessed, including thermal spraying of a CoNiCrAlY alloy material using the High Velocity Oxygen Fuel (HVOF) process and vacuum plasma spraying (VPS). It was determined that the blocking issue in the HVOF process can be mitigated by modifying the spray angle between the torch and the substrate. Additionally, oxidation-resistant nickel-aluminide diffusion layers were produced on nickelbased alloys using the pack-cementation process, which effectively prevented blocking. Subsequent steps involved the coating of the samples using suspension plasma spraying (SPS) and plasma spray physical vapor deposition (PS-PVD). It was determined that the SPS process necessitates suitable pretreatment of the surface, such as sandblasting, to ensure stable bonding of the ceramic top layer. The results also demonstrated that the PS-PVD process is particularly effective in maintaining the cooling holes free, as it results in effective deposition from the gas phase, with most of the plasma gas flowing around the cooling holes. Moreover, both experimental and simulation-based evidence demonstrated that the SPS process can achieve reduced blockage compared to the APS process. In addition, it has been proven both experimentally and through simulations that the SPS process enables reduced blockage compared to atmospheric plasma spraying (APS). This is achieved by adjusting the spray parameters, such as the spray distance or the total gas flow rate, as well as the cooling air pressure. Thermal cycling tests have also shown that SPS and PS-PVD processes can be used to produce coatings with a comparable or even improved service life compared to APS coatings on substrates with cooling holes. This research project was financially supported within the framework of LuFo by the Federal Republic of Germany, Federal Ministry of Economics and Climate Protection, based on a resolution of the German Bundestag (FKZ: 20T1702) and by Rolls-Royce Deutschland Ltd & Co KG.
001053957 536__ $$0G:(DE-HGF)POF4-1241$$a1241 - Gas turbines (POF4-124)$$cPOF4-124$$fPOF IV$$x0
001053957 8564_ $$uhttps://juser.fz-juelich.de/record/1053957/files/Energie_Umwelt_687.pdf$$yOpenAccess
001053957 909CO $$ooai:juser.fz-juelich.de:1053957$$popenaire$$popen_access$$pVDB$$pdriver$$pdnbdelivery
001053957 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)188375$$aForschungszentrum Jülich$$b0$$kFZJ
001053957 9131_ $$0G:(DE-HGF)POF4-124$$1G:(DE-HGF)POF4-120$$2G:(DE-HGF)POF4-100$$3G:(DE-HGF)POF4$$4G:(DE-HGF)POF$$9G:(DE-HGF)POF4-1241$$aDE-HGF$$bForschungsbereich Energie$$lMaterialien und Technologien für die Energiewende (MTET)$$vHochtemperaturtechnologien$$x0
001053957 9141_ $$y2026
001053957 915__ $$0StatID:(DE-HGF)0510$$2StatID$$aOpenAccess
001053957 915__ $$0LIC:(DE-HGF)CCBY4$$2HGFVOC$$aCreative Commons Attribution CC BY 4.0
001053957 920__ $$lyes
001053957 9201_ $$0I:(DE-Juel1)IMD-2-20101013$$kIMD-2$$lWerkstoffsynthese und Herstellungsverfahren$$x0
001053957 980__ $$aphd
001053957 980__ $$aVDB
001053957 980__ $$aUNRESTRICTED
001053957 980__ $$abook
001053957 980__ $$aI:(DE-Juel1)IMD-2-20101013
001053957 9801_ $$aFullTexts