% IMPORTANT: The following is UTF-8 encoded.  This means that in the presence
% of non-ASCII characters, it will not work with BibTeX 0.99 or older.
% Instead, you should use an up-to-date BibTeX implementation like “bibtex8” or
% “biber”.

@ARTICLE{Mcke:16321,
      author       = {Mücke, R. and Büchler, O. and Bram, M. and Leonide, A.
                      and Ivers-Tiffée, E. and Buchkremer, H.P.},
      title        = {{P}reparation of functional layers for anode-supported
                      solid oxide fuel cells by the reverse roll coating process},
      journal      = {Journal of power sources},
      volume       = {196},
      issn         = {0378-7753},
      address      = {New York, NY [u.a.]},
      publisher    = {Elsevier},
      reportid     = {PreJuSER-16321},
      pages        = {9528 - 9535},
      year         = {2011},
      note         = {Record converted from VDB: 12.11.2012},
      abstract     = {The roll coating technique represents a novel method for
                      applying functional layers to solid oxide fuel cells
                      (SOFCs). This fast process is already used for mass
                      production in other branches of industry and offers a high
                      degree of automation. It was utilized for coating specially
                      developed anode (NiO + 8YSZ, 8YSZ: 8 $mol\%$
                      yttria-stabilized zirconia) and electrolyte (8YSZ)
                      suspensions on green and pre-sintered tape-cast anode
                      supports (NiO + 8YSZ). The layers formed were co-fired in a
                      single step at 1400 degrees C for 5 h. As a result, the
                      electrolyte exhibited a thickness of 14-18 mu m and
                      sufficient gas tightness. Complete cells with a
                      screen-printed and sintered La0.65Sr0.3MnO3-delta (LSM)/8YSZ
                      cathode yielded a current density of 0.9-1.1 A cm(-2) at 800
                      degrees C and 0.7 V. which is lower than the performance of
                      non-co-fired slip-cast or screen-printed Julich standard
                      cells with thinner anode and electrolyte layers. The
                      contribution of the cell components to the total
                      area-specific resistance (ASR) was calculated by analyzing
                      the distribution function of the relaxation times (DRTs) of
                      measured electrochemical impedance spectra (EIS) and
                      indicates the potential improvement in the cell performance
                      achievable by reducing the thickness of the roll-coated
                      layers. The results show that the anode-supported planar
                      half-cells can be fabricated cost-effectively by combining
                      roll coating with subsequent co-firing. (C) 2011 Elsevier
                      B.V. All rights reserved.},
      keywords     = {J (WoSType)},
      cin          = {IEK-1},
      ddc          = {620},
      cid          = {I:(DE-Juel1)IEK-1-20101013},
      pnm          = {Rationelle Energieumwandlung / SOFC - Solid Oxide Fuel Cell
                      (SOFC-20140602)},
      pid          = {G:(DE-Juel1)FUEK402 / G:(DE-Juel1)SOFC-20140602},
      shelfmark    = {Electrochemistry / Energy $\&$ Fuels},
      typ          = {PUB:(DE-HGF)16},
      UT           = {WOS:000295602400056},
      doi          = {10.1016/j.jpowsour.2011.07.063},
      url          = {https://juser.fz-juelich.de/record/16321},
}