000825081 001__ 825081
000825081 005__ 20240708132823.0
000825081 037__ $$aFZJ-2016-07561
000825081 041__ $$aEnglish
000825081 1001_ $$0P:(DE-Juel1)156509$$aDashjav, Enkhtsetseg$$b0$$eCorresponding author
000825081 1112_ $$aBunsen-Kolloquium: Solid-State Batteries II$$cFrankfurt/Main$$d2016-11-23 - 2016-11-25$$wGermany
000825081 245__ $$aProperties of Li1.5Al0.5Ti1.5(PO4)3 sheets made by tape casting
000825081 260__ $$c2016
000825081 3367_ $$033$$2EndNote$$aConference Paper
000825081 3367_ $$2BibTeX$$aINPROCEEDINGS
000825081 3367_ $$2DRIVER$$aconferenceObject
000825081 3367_ $$2ORCID$$aCONFERENCE_POSTER
000825081 3367_ $$2DataCite$$aOutput Types/Conference Poster
000825081 3367_ $$0PUB:(DE-HGF)24$$2PUB:(DE-HGF)$$aPoster$$bposter$$mposter$$s1481825939_2002$$xAfter Call
000825081 520__ $$aTape casting is a well-established shaping technique for ceramic materials and can be scaled up with existing experience. Recently we started the preparation of dense electrolyte sheets for Li-ion batteries. Sol-gel prepared nano-sized powder of Li1.5Al0.5Ti1.5(PO4)3 [1] was successfully tape-cast using the doctor blade method. Plain sintered sheets with thicknesses between 50 µm and 150 µm could be fabricated with a maximum size of 10 cm². The densification and ionic conductivity at different sintering temperatures were investigated by microstructural analysis and impedance spectroscopy, respectively. The average total ionic conductivity was in the range of 0.2 mS/cm, which is still lower than powder pellets [1], but already twice as good as commercially available glass-ceramics [2]. The results show that the density and the microstructure are very sensitive to sintering temperatures and dwell time. The ionic conductivities and the sintered thicknesses are presented in Table 1. The highest ionic conductivity of 0.3 mS/cm is achieved at 1000°C sintering temperature. The parameters are actually under optimization with respect to higher density, better homogeneity and reduced crack formation. For the mechanical stability 4 point bending strength tests were carried out on samples sintered at 900°C with dimensions of h = 150 µm, b = 1 cm, l = 5 cm resulting in a modulus of elasticity of E = 67 GPa ±14 GPa, and a specific fracture resistance σb = 62 MPa ±7 MPa. The stability of these sheets is promising for further use in any battery design with ceramic separator.
000825081 536__ $$0G:(DE-HGF)POF3-131$$a131 - Electrochemical Storage (POF3-131)$$cPOF3-131$$fPOF III$$x0
000825081 7001_ $$0P:(DE-Juel1)169592$$aGellert, Michael$$b1
000825081 7001_ $$0P:(DE-Juel1)129628$$aMa, Qianli$$b2
000825081 7001_ $$0P:(DE-Juel1)145209$$aGrüner, Daniel$$b3
000825081 7001_ $$0P:(DE-Juel1)151260$$aPristat, Sylke$$b4
000825081 7001_ $$0P:(DE-Juel1)129667$$aTietz, Frank$$b5
000825081 909CO $$ooai:juser.fz-juelich.de:825081$$pVDB
000825081 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)156509$$aForschungszentrum Jülich$$b0$$kFZJ
000825081 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)169592$$aForschungszentrum Jülich$$b1$$kFZJ
000825081 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)129628$$aForschungszentrum Jülich$$b2$$kFZJ
000825081 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)145209$$aForschungszentrum Jülich$$b3$$kFZJ
000825081 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)151260$$aForschungszentrum Jülich$$b4$$kFZJ
000825081 9101_ $$0I:(DE-588b)5008462-8$$6P:(DE-Juel1)129667$$aForschungszentrum Jülich$$b5$$kFZJ
000825081 9131_ $$0G:(DE-HGF)POF3-131$$1G:(DE-HGF)POF3-130$$2G:(DE-HGF)POF3-100$$3G:(DE-HGF)POF3$$4G:(DE-HGF)POF$$aDE-HGF$$bEnergie$$lSpeicher und vernetzte Infrastrukturen$$vElectrochemical Storage$$x0
000825081 9141_ $$y2016
000825081 915__ $$0StatID:(DE-HGF)0550$$2StatID$$aNo Authors Fulltext
000825081 920__ $$lyes
000825081 9201_ $$0I:(DE-Juel1)IEK-1-20101013$$kIEK-1$$lWerkstoffsynthese und Herstellungsverfahren$$x0
000825081 980__ $$aposter
000825081 980__ $$aVDB
000825081 980__ $$aUNRESTRICTED
000825081 980__ $$aI:(DE-Juel1)IEK-1-20101013
000825081 981__ $$aI:(DE-Juel1)IMD-2-20101013